Grand Gate Repair of Concord Company repairs automatic and manual gates across Concord, California: driveway, swing, and sliding gates in iron, wood, vinyl, aluminum, steel, and chain link, plus openers, sensors, keypads, and control boards. We diagnose first, agree the work on inspection, and test the gate with you before we leave.
Tell us what is happening. Our local team will confirm your visit shortly.
Call Now +19252658944 → Call during open hours, 8:00 AM to 8:00 PM daily.Upfront optionsNo work before you approve it
Respectful serviceClean work areas, clear communication
Quote on inspectionFigure agreed after diagnosis, before work
Concord-based teamServing Concord, CA from Clayton Rd
Grand Gate Repair of Concord Company repairs and installs automatic and manual gates across Concord, California: driveway gates, swing and sliding gates, iron, wood, vinyl, aluminum, steel, and chain link, plus openers and access controls. One call covers diagnosis, repair, and a tested, working gate.
What sets us apart is diagnosis before repair. Concord gates fail in local ways: posts shift in expansive clay, wood rots at grade and warps in summer heat, hillside gates drag on slopes, and shared entrances wear out faster. We work from Downtown and Todos Santos to Clayton Valley, Ygnacio Valley, and Crystyl Ranch, and we answer the phone during open hours, 8:00 AM to 8:00 PM daily.
Whether your gate drags, the keypad stopped responding, or the whole opener is dead after a power surge, we handle it. We cover every gate type and the opener brands commonly found in Concord, and we diagnose the fault before quoting the fix.
Automatic Gate Repair
Automatic gates that stop mid-travel, reverse, or ignore the remote usually have a sensor, board, or motor fault. We test the control board, photo eyes, and limit switches, then repair or replace the failed part and test the full cycle with you.
Explore →
Driveway Gate Repair
Driveway gates take the most use: posts shift in Concord's expansive clay, wheels wear flat, and hinges sag. We re-level sagging hinges, replace worn wheels, and true up the track so the gate rolls without dragging, on single and double gates.
Explore →
Electric Gate Repair
Electric gate faults are usually power or signal: a tripped breaker, a surge-damaged board, or a remote that lost its code. We check power at the board, test the transformer, and reprogram remotes and keypads on site, with safety sensors tested after.
Explore →
Gate Opener Repair
A humming opener that will not move the gate points to a capacitor, stripped gear, seized drive, or a bound gate. We test the motor and gearing, check the manual release, and repair or replace the opener to match the gate's weight and use.
Explore →
Sliding Gate Repair
Sliding gates jump the track when rollers wear or the track bends or sinks. We replace rollers, straighten or replace bent track sections, and adjust the guide so the gate glides. If your sliding gate is grinding, stop running it before the motor is damaged.
Explore →
Swing Gate Repair
Swing gates sag at the hinge and drift out of square, which loads the opener. We repair or replace hinges, brace the frame, and reset the arm geometry, on single-leaf and double swing gates, including gates on hillside lots.
Explore →
Iron Gate Repair
Rust works into iron gates at hinges and post bases, where it becomes a safety problem. We cut out rusted sections, weld in new steel, and refinish the repair so it blends. Iron-style and tubular steel gates are core work for us.
Explore →
Wooden Gate Repair
Wood gates rot at the bottom rail and split at hinge bolts, and Concord rain and summer heat speed both. We replace damaged panels and rails, sister in new framing, and rehang the gate so it swings true, matching stain and finish.
Explore →
Chain Link Gate Repair
Chain link gates bind when the post leans or the frame twists. We reset leaning posts in concrete, replace bent frames, and replace worn hinges and latches, for yards, kennels, and other fenced areas around Concord.
Explore →
Vinyl Gate Repair
Vinyl gates crack at hinge points and bow in summer heat. We replace broken pickets and rails, reinforce hinge mounts, and re-square the frame, matching common vinyl profiles where a panel must be replaced.
Explore →
Aluminum Gate Repair
Aluminum gates are light, which is why they go out of square and rattle. We tighten and replace hinges, repair cracked joints, and adjust the frame so it latches clean, touching up powder-coated finishes after repair work.
Explore →
Steel Gate Repair
Steel gates take impacts and heavy use. We straighten bent frames, repair cracked welds, and rebuild hinge plates that have torn loose, adding gussets where the same spot has failed before.
Explore →
Gate Motor Repair
Gate motors fail from heat, water, and worn internal parts. We test the motor under load, replace failed capacitors and drive parts where possible, and reseal housings against rain. If the motor is beyond repair, we quote a replacement matched to the gate.
Explore →
Gate Control Board Repair
A power surge can leave a control board dead or forgetful, with lost limits and codes. We test board outputs, replace blown fuses and failed relays, and reprogram travel limits and codes, testing safety protection before handover.
Explore →
Gate Remote Repair
Remotes stop working when the battery dies, the code drops, or the receiver fails. We test the remote, replace batteries, and reprogram it to your receiver. If the receiver has failed, we replace it and program every remote on the property.
Explore →
Gate Sensor Repair
Safety sensors that beep or stop the gate mid-close are usually misaligned, dirty, wet, or failed. We realign photo eyes, dry housings, and replace failed sensors, and we never bypass a sensor to force a gate closed.
Explore →
Gate Keypad Repair
Keypads quit when water gets in or wiring corrodes at the post. We test power at the keypad, replace the unit where needed, and reprogram your codes, testing wireless and wired keypads with you present.
Explore →
Gate Hinge Repair
Sagging gates almost always trace back to worn or torn hinges, or to a post that has moved. We repair or replace hinges, shim the gate back to square, and check the post, since adjusting a hinge on a leaning post will not hold.
Explore →
Gate Roller Repair
Flat-spotted or seized rollers make a sliding gate grind and shake. We replace rollers, align the gate in the track, and check ground clearance, so the gate rolls without dragging or jumping the rail.
Explore →
Gate Track Repair
A bent, rusted, or debris-filled track stops a sliding gate at the same spot on every cycle. We clear, straighten, or replace track sections, repair the track bed where it has sunk, and inspect rollers at the same time.
Explore →
Gate Latch Repair
A latch that will not catch is usually alignment, not the latch itself: a sagging gate, a shifted post, or a worn closer. We realign the gate, replace worn latches and closers, and check self-closing and self-latching on pool gates against the 60-inch rule.
Explore →
Gate Lock Repair
Gate locks fail from corrosion, misalignment, and worn cylinders. We realign the gate first, then repair or replace the lock so it engages cleanly without forcing, and confirm keys and codes work before leaving.
Explore →
Gate Panel Repair
Damaged gate panels, whether dented metal, cracked vinyl, or rotted wood boards, can often be repaired without replacing the whole gate. We replace the damaged section, match the finish, and check the frame still holds square.
Explore →
Gate Post Repair
A leaning gate post throws off the whole gate. In Concord, expansive clay and root heave are frequent causes. We dig out failed posts, reset them in concrete, brace the gate while it cures, and check latch alignment after.
Explore →
Gate Welding Repair
Cracked welds and torn hinge plates need real welding, not filler. We grind out the crack, weld it, and dress the joint so it holds under load, on steel and iron gates around Concord.
Explore →
Gate Painting and Refinishing
Rust and peeling paint are early signs a gate is failing. We wire-brush rust, prime bare metal, and apply a finish coat suited to Concord sun and rain. Wood gates get sanded, sealed, and stained.
Explore →
Gate Installation
A new gate starts with the lot: slope, clearance, swing or slide run, and power. We set posts, hang the gate, mount the opener, and wire safety sensors, testing entrapment protection and full travel before handover.
Explore →
Gate Replacement
When a gate is rusted through, rotted at the posts, or too bent to hold square, replacement beats another repair. We remove the old gate, set new posts where needed, and install a gate built for your opening and daily use.
Explore →
We are a Concord gate repair company, not a call centre. Our work starts with diagnosis, includes a safety test on automatic gates, and ends with a quote agreed on inspection before work starts.
We find the failed part first: sensor, board, motor, hinge, roller, track, or post. In Concord, a sagging gate is often a post moved by contractor-reported expansive clay, not a dead opener, and diagnosing that correctly is what keeps a repair from repeating.
Automatic gates we work on get their safety sensors, safety edges, and reversal tested before it returns to normal use. A gate that runs but does not reverse on obstruction is not a finished job, and we never bypass a sensor to make a gate close.
You agree the scope and the figure after diagnosis, before work starts. If diagnosis finds a second failed part, we say so before doing that work, so there is no surprise at the end of the visit.
Tell us what the gate is doing: humming, stuck open, off track, dragging, or dead. We ask for the gate type and opener brand so we can talk through the likely fault before a visit.
We test power at the board, check the safety sensors, and move the gate by hand where it is safe to do so, to find the real fault. You agree the scope and figure on inspection before any work starts.
We repair or replace the failed part: hinges, rollers, track sections, boards, sensors, or motors. Then we run the gate through a full open and close cycle and test its safety protection.
We show you what failed and what was done, and note anything to watch, such as a post to monitor or a track to keep clear. You have our number if the gate acts up again.
Tell us what the gate is doing: humming, stuck open, off track, dragging, or dead. We ask for the gate type and opener brand so we can talk through the likely fault before a visit.
Most calls come down to a handful of failures: a gate that will not close, a motor humming but not moving, a keypad or remote that stopped responding, or a gate sagging and dragging. Here is how we handle the ones we see most around Concord, from flat valley lots to hillside driveways.
Ask a pro →That is usually a misaligned, dirty, or wet safety sensor, or a gate binding on a shifted post. We realign the photo eyes, clear the track, check the post, and test the safety circuit before the gate returns to use.
A humming motor is trying against something: a bound gate, a failed capacitor, or a seized drive. We release the gate by hand to separate a mechanical bind from a motor fault, so the motor is not burned out by repeated tries.
No response usually means power, wiring, moisture, a dead battery, or a lost code. We work the chain in order, remote, receiver, keypad, and operator, and reprogram codes where they have been lost after a surge.
Sagging and dragging in Concord usually trace to hinge wear plus post movement in expansive clay, or to worn rollers and a bent track on sliding gates. We put the hinge, post, or track right first, then rehang or re-rail the gate.
We do not publish a star rating or review count on this site, because directory figures for this business conflict and have not been verified from a single live source. Read what customers say where reviews are published, and judge us on the visit itself.
Call Grand Gate Repair of Concord Company at +1 925-265-8944. We are open Monday through Sunday, 8:00 AM–8:00 PM daily, at 2727 Clayton Rd, Concord, CA 94519, and we will talk through your gate problem and arrange an inspection.
We serve Concord, CA, from the flat valley floor to the hillside lots above it: Downtown and Todos Santos, the Monument Corridor, Sun Terrace, Dana Estates, Four Corners, Clayton Valley, Ygnacio Valley, Cowell, and Crystyl Ranch among them. Flat lots favour swing gates and simple footings; hillside lots need slope-aware gates, drainage at tracks, and stronger posts. If your street is in Concord, call with your address and we will confirm coverage.
Not sure you are in range? Call with your address and ZIP code and we will check.
Straight answers to the questions we get most from Concord homeowners about cost, hiring a pro, hours, and what a repair visit covers.
+19252658944 →It depends on the gate type and material, the opener and its parts, whether structural work such as a post or track repair is needed, and access. We quote on inspection after diagnosis, so the figure you agree to is for your gate and your fault, not a fixed price for a different job.
Ask what licence class covers the work, whether the job needs a permit, and how safety protection will be tested after the repair. For pool gates, check the 60-inch latch rule. Keep the quote and the scope in writing before work starts.
Grand Gate Repair of Concord Company is open Monday through Sunday, 8:00 AM to 8:00 PM daily. Call 925-265-8944 during those hours, or find us at 2727 Clayton Rd, Concord, CA 94519.
Diagnosis of the fault, repair or replacement of the failed part, and a test of the whole gate system, including hinges, rollers, tracks, motors, control boards, remotes, keypads, and safety sensors, with a walkthrough of what failed.
Usually a safety sensor is blocked, dirty, or misaligned, the track is obstructed, travel limits have drifted, or the gate binds on worn hinges or a shifted post. Never bypass a safety sensor to force a close.
Call Grand Gate Repair of Concord Company at +1 925-265-8944 for gate repair in Concord, CA. We are open Monday through Sunday, 8:00 AM–8:00 PM daily, at 2727 Clayton Rd, Concord, CA 94519.
Call Now →Call us at +1 925-265-8944 during open hours, Monday through Sunday, 8:00 AM–8:00 PM daily. Tell us the gate type and opener brand and what the gate is doing, and we will talk through the next step. Our address is 2727 Clayton Rd, Concord, CA 94519.